Showing 1–16 of 112 results
-
$322.00
Features & Benefits:-* Chrome-Moly Pushrods.* Replaces OEM # 17921-83, 17924-83, 17927-83, 17930-83 & 17900-87Tech Tips:-* These EVO Adjustable pushrods are NON EZ-install – Requires Top Rocker Cover removal for fitment* Prior to Start-up, the engine should be wound over with spark plugs removed until oil reaches the top pushrod ball / rocker arm socket.Proudly Made…
-
$322.00
Features & Benefits:-* Chrome-Moly Steel Pushrods.* Replaces OEM # 17897-89 & 17904-89Tech Tip:-* XL’91-03 models must buy CM-2255-36 and CM-2254-2.* XL’04up models must buy CM-2253-36.* On 1991up models, it is necessary to disassemble the rocker arm/rocker box to remove the stock one piece pushrod cover.* Prior to Start-up, the engine should be wound over with…
-
$156.00
Features & Benefits:-* Dual Fire High Output Andrews Super Volt Coil delivers 30,000+ volts. * 4.8 Ohms all HD bikes with 12 volt point type ignitions. * Also fits the very first 1979-80 HD type prestolite electronic Ignition* Coils will produce more voltage than stock coils.* Replaces OEM # 31609-65AProudly Made by Andrews Products!
-
$378.00
Features & Benefits:-* Bolt-in street cam for light bikes (FXRS,etc.). Lots more mid-range and upper end power. Smooth idle 2800 to 6500 RPM cam with stock heads.* Works with stock valve springsSuggested Additional Purchase:Adjustable Pushrod Kit: # SS930-0052 or # AP-292245Lifters: # FE-4061 or # SS33-5352Cam Change Gasket Kit: 1970-1992 # JGI-25225-70-KX or 1993-1999 #…
-
$711.00
* Bolt-in, broad tip cams: 96, 103 Limited and CVO 110 engines. Max torque: 2200 – 5600 RPM* Uses OEM valve springs
-
$456.00
M485 – Bolt in cam for 114ci engines. Aggressive, mid to high RPM power cam for middle to heavy weight bikes (2500-5600+ RPM)A nice cam in 124/128ci builds with higher compression than stockTech Tips:-Due to the high lift nature of this cam, tappet cuffs are required for installation. Use part # SS330-0655
-
$541.00
Features & Benefits:-* Made from high nickel alloy* Heat treated and shot-peened to give maximum durability & strength. * Replaces OEM # 35042-91Tech Tips:-Length = 13.605in.
-
$426.00
Features & Benefits:-* Made from high nickel alloy* Heat treated and shot-peened to give maximum durability & strength. * Replaces OEM # 35039-70A
-
$447.00
Features & Benefits:-* Made from high nickel alloy* Heat treated and shot-peened to give maximum durability & strength. * Replaces OEM # 35040-50
-
$353.00
Suggested Additional Purchase: Part # PBI-291 (Lock Nut)Features & Benefits:-* 30 Tooth Power Pulley gives 6.4% more RPM (200 RPM increase @ 60 MPH, high gear)* Speedo Recalibration Unit NMZ-NSIM-01 is available if required.* Long Life SteelTech Tips:- * Pulleys with less teeth than stock, rear axle must be adjusted back. * Each tooth change…
-
$353.00
Suggested Additional Purchase: Part # PBI-291 (Lock Nut)Features & Benefits:-* 31 Tooth Power Pulley gives 3% more RPM* Speedo Recalibration Unit NMZ-NSIM-01 is available if required.* Long Life SteelTech Tips:- * Pulleys with less teeth than stock, rear axle must be adjusted back. * Each tooth change on transmission sprocket = + /– .125 inch…
-
$353.00
Requires the purchase of:BAI-D26-0205 – Trans Nut Lock Plate Kit; BT’92-06 & XL’91upJGI-12067-A – Seal; Trans Main BT’L94-06 5spd Models OnlyBCM-7342 – Main Drive Seal Spacer; BT’L94up 5spdFeatures & Benefits:-* 33 Tooth Overdrive Pulley 3% Less RPM* Speedo Recalibration Unit DAK-SIM-1A is available if required.* Long Life SteelTech Tips:-* Fits 1986-2006 HD and aftermarket 5…
-
$129.00
Features & Benefits:-* This gear will change your timing from +4° for more torque, to -4° for less compression and for easier starting.* Made in USAFitment:-Twin Cam 2007 – 2017 Twin Cam engines, including 2006 Dyna & Milwaukee Eight engines.
-
$204.00
* 34 tooth splined cam sprocket kit* Stock on 2000-2006 Models* Required when installing chain drive cams on 1999 Twin Cam Models* Andrews heat treated steel cam drive sprockets are an upgrade for rear camshafts on engines with silent chain cam drives. * Kit includes three spacer shims and one grade 8 bolt and hardened…
-
$463.00
Features & Beneifts:-* Chrome-Moly pushrods* EVO pushrods with EZ-install ends. * If you are installing bolt-in cams, this is a big plus* Replaces OEM # 17921-83, 17924-83, 17927-83, 17930-83 & 17900-87Tech Tips:-* EZ-install pushrods can be installed without removing gas tanks or rocker boxes. * Prior to Start-up, the engine should be wound over with…
-
$247.00
Features & Benefits:-* Chrome-Moly Steel Pushrods for maximum strength.* Stock diameter tubing – eliminates pushrod cover interferenceTech Tips:-* These pushrods replace the OEM steel rods* Works with the stock hydraulic unit JM-2370 (OEM 17920-53A) and the stock style Hydraulic Tappet JM-2462-1 (OEM 185522-53A) * Also works with JM-2459-1 PowerGlide Hydraulic TappetProudly Made in the USA…
Showing 1–16 of 112 results