3 in 1 OBD TR4 Cable. Fits all Models.
$246.00This cable includes a 4 pin connector, 6 pin connector & OBD connector for 2021 Models.
Showing 1–16 of 91 results
This cable includes a 4 pin connector, 6 pin connector & OBD connector for 2021 Models.
Features & Benefits:-* Suggested additional purchase, Timken Bearing # SS31-4013Tech Tips:-* May cause a slight increase in engine noise* Replaces OEM # 34822-08
Licence Number:Features & Benefits:-This code will add two (or more) model years to your current Centurion Super Pro License. Example – updating a 2017 Centurion Super Pro license to work with 2019 and later current models.For a one year license, use part number TR200017. Example – updating a 2017 Centurion Super Pro license to work…
* The industry’s only complete, professional diagnostic tool designed for independent, professional repair facilities* Communicates with most 1997 and later Harley-Davidson models using the included VCM-TR4 communication module and cables* Re-flash blank ECUs, program VINs and key fobs* Perform radio and speaker calibration* Perform speedo calibration* ABS bleeding and solenoid testing* Read and clear diagnostic…
JIMS Wrist Pin Clip Remover and Installer for Twin Cam Pistons* Use tools to easily remove and install wire type wrist pin clips without damage to the piston
Features & Benefits:-* Fits all H-D Models.* Supplied with six bands.* Works with piston sizes from 2-7/8in. to 4-3/8in..* Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression.* Will Not Break or Damage Rings.Proudly Made in the USA by JIMS !
Cylinder hold down nuts are an effective way to keep the cylinders in place when the heads are removed from the engine. This is particularly useful when installing the second cylinder over the piston and rings after the first cylinder has been installed. It is also advantageous to have the cylinders secured when rotating the…
* Also fits Milwaukee 8* Designed to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket bolts* Made of non-marring Delrin* Instructions included* Made in the U.S.A.
Features & Benefits:-* Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams.* Also checks spring loads on chain tensioners* Includes instructionsTech Tips:-* Will Not Fit Dyna 2006.Proudly Made in the USA by JIMS !
* Presses in the inner cam bearing* Designed to press from letter side of the inner cam bearing by putting all the pushing pressure to the very outer wall of bearing shell* Eliminates any damage to the bearing, cam and cases* Stops at the case and sets the bearing depth to .023in. to .028in. below…
Features & Benefits:-* Aligns Oil Hole from Crank Case to Tappet Block on Late Shovel & Evo Engines.* Aligns the Oil Pump to the Cam Plate on Twin Cam Engines.* Aligns Lower Rocker Cover to Cylinder Head on Evo Style Heads, including Sportster & Buell (2 Required). * 1/4in.-20 thread.Proudly Made in the USA by…
Features & Benefits:-* Sold Each.Proudly Made in the USA by Bender Cycle !
Features:* No Calibration required* Soft start technology* 2 analog outputs* 1 digital input, 1 digital output* 2 Bosch LSU 4.2 Sensors* Compatible with multiple fuels* Sensor is hand tested* Digital precisionThis wideband oxygen sensor interface kit is essential for anyone looking to get robust and accurate data to tune a bike. The TRO2 is a…
What was the first thing JIMS did when we took delivery of our new M8 test bike? We removed the engine to take a peek inside, of course. Instantly we realized a new engine stand was in order! * Steel powder-coated construction* Make working on motors easier with better access* Made in the U.S.A
Showing 1–16 of 91 results
No products in the cart.