Replacement 3/4in. Wheel Bearing Puller Tool. Fits JIMS 2000up Wheel Bearing Remover & Installer # JM-939.
$107.00Features & Benefits:-* Replacement Jims Wheel Bearing Puller .750in. I.D.Proudly Made in the USA by JIMS !
Showing 17–32 of 171 results
Features & Benefits:-* Replacement Jims Wheel Bearing Puller .750in. I.D.Proudly Made in the USA by JIMS !
Features & Benefits:-* Replacement 25mm Puller Only.Proudly Made in the USA by JIMS !
Features & Benefits:-* Replacement Jims Wheel Bearing Puller 1.00in. I.D.Proudly Made in the USA by JIMS !
Features & Benefits:-* Removes & installs the 25mm H-D bearing.* Removes ABS or non ABS Wheel Bearings on most of 2008up Wheels. * This tool must be used with the earlier JIMS wheel bearing Installer & Remover Tool # JM-1042.Proudly Made in the USA by JIMS !
Suggested Additional Purchase* Features a hardened ball-bearing at the valve head end to eliminate damage to valves* Comes with new valve collar receiver for safer tool usage* Made in the USA!Tech Tips:-* 2005-2017 Require Adapter Part Number: JM-988 * 2017up(M8) Require Adapter Part Number: JM-5808
Features & Benefits:-* Short Socket.* Designed to Remove, Install & Properly Tighten the Front Final Drive Sprocket/Pulley Nut.* Although the much longer Big Twin socket will fit the nut, the Mainshaft on XL models does not extend through for the guidance collar to ensure correct alignment. * This shorter socket is easier and safer to…
Features & Benefits:-* Fits 4 & 5 Speed Models* Heavy-Duty thick wall tube. * Extra long two piece design, inner collar will retain wrench to nut for safer service work.* 1-7/8in. hex.* 1/2in. Drive.Tech Tips:-* Will Not Fit 6 Speed Transmissions.Proudly Made in the USA by JIMS !
* Inner collar will retain wrench to nut for safer work* Remove hex nut from end of main drive gear that secures the rear drive transmission pulley* Extra-long two-piece design* Made in the U.S.A.* Replaces OEM # 94141-10
* Lock your transmission pulley for removing or installing pulley nut* Fits OEM & Aftermarket 5 & 6 speed transmissions.* Made in the U.S.A.Tech Tips:-* Does NOT fit Sportster Models (They require # JM-2262)
* Used to remove and install top fork-tube plug* Fits 41mm forks* Made in the U.S.A* Note: this tool works on the top fork plug that screws into the fork tube.* Slider tube cap socket JM-2244 may also be required
35mm Slider tube top cap nut. Use’s 3/8in. drive* Used to remove and install top fork nuts on fork tubes* Rubber protector inside socket protects chrome finish* Will clear under most handlebars* Made in the U.S.A.
Installing fork tube caps requires compressing the spring while rotating the cap. This is not particularly difficult with fork legs that have been removed from the bike and securely mounted in a work area. However, on the bike, the task can become almost impossible because of restricted work area and other components getting in the…
The new Softail inverted forks utilizes a unique inner fork nut (Castlenut) to secure and compress the fork spring. This one-piece solid steel socket is designed to help the technician by securing the socket to the joint rod prior to final assembly.Fitment:M8 Softail with Inverted forks (i.e. FXDR, Sport Glide, Fat Bob, Low Rider SV-Rod…
* Used for removing and installing the Timken® bearing outer race snap ring.* A must for replacing rings in OEM and aftermarket cases* Made in the U.S.A.
Showing 17–32 of 171 results
1 × $2,814.00
Subtotal: $20,395.00