Showing 1–16 of 222 results
-
$172.00
Fitment Note: 2006-2017 Dyna & 2007up Models:- The bearing race is installed from factory with RED Locktite along with the trans pulley nut. This has been causing some problems. The two items must be heated prior to pulling the race or removing the nut with the sprocket wrench.
-
-
$67.00
Features & Benefits:-* Includes O’Ring.* Standard Outside Diameter is .940in..* Sold as a Pair.* Replaces OEM # 33288-37Proudly Made in the USA by JIMS !
-
$371.00
Features & Benefits:-* Machined from solid bronze bar stock.* Hold concentricity to less than .0002in..* Includes Sprocket Shaft # JM-23909-80.* Includes Sprocket Side Nut # JM-24003-55.* Flywheel Side Nut # JM-24017-80.* Key # JM-2489.Proudly Made in the USA by JIMS !
-
$717.00
Jims A Cut Above Time-Saver 5-Speed Transmission Master Kit* Kits include bearings, retaining rings, spacers, locknuts and gaskets and seals for Big Twin* Made in the USAWe use JIMS# proven transmission parts to start with, then top it off with a JIMS# gasket set, together in one convenient package. This is a big time saver.Tech…
-
$180.00
Features & Benefits:-* Short Socket.* Designed to Remove, Install & Properly Tighten the Front Final Drive Sprocket/Pulley Nut.* Although the much longer Big Twin socket will fit the nut, the Mainshaft on XL models does not extend through for the guidance collar to ensure correct alignment. * This shorter socket is easier and safer to…
-
$463.00
Features & Benefits:-* Fits 4 & 5 Speed Models* Heavy-Duty thick wall tube. * Extra long two piece design, inner collar will retain wrench to nut for safer service work.* 1-7/8in. hex.* 1/2in. Drive.Tech Tips:-* Will Not Fit 6 Speed Transmissions.Proudly Made in the USA by JIMS !
-
$461.00
* Inner collar will retain wrench to nut for safer work* Remove hex nut from end of main drive gear that secures the rear drive transmission pulley* Extra-long two-piece design* Made in the U.S.A.* Replaces OEM # 94141-10
-
-
$143.00
Features & Benefits:-* Designed to lock the camshafts & crankshaft sprockets when removing, replacing & torquing the sprocket bolts.* Made of non-marring Delrin.* Includes Instructions.Tech Tips:-* Will Not Fit Dyna 2006.Proudly Made in the USA by JIMS !
-
$136.00
Features & Benefits:-* Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams.* Also checks spring loads on chain tensioners* Includes instructionsTech Tips:-* Will Not Fit Dyna 2006.Proudly Made in the USA by JIMS !
-
$476.00
Use on all Big Twin 1958-99 single cam only. (Note: Includes aftermarket motors.)
-
$49.00
* Size:- (M) Medium. * Colour:- White.
-
$93.00
* Smooth finish for a longer seal life* 1.7in. ID* Sold each* Made in the U.S.A* Replaces OEM # 33334-94
-
$295.00
* Reduces shifter free play* Assembly includes plate (replaces OEM #35068-79)* Spring (#34087-79)* Pawl plate (#34086-79)* Shifter shaft (#34084-86)* Spring (#34083-79)* Pin (#34082-79)* Washer (#6016) * Retaining ring (#11016)* Made in the U.S.A.
-
$69.00
* Bushings are made from solid bronze bar stock* Machined in one operation with a tolerance of .0002in.* Feature a lead-in for ease of installation* Big Twin Standard O.D. is 1.2015in.* Standard I.D. is 1.000in.* Sold eachTech Tips:-* Use JM-1012-70TB to install and JM-1023-70 reamer to size bushing.* Replaces OEM # 25581-70Made in the U.S.A….
Showing 1–16 of 222 results