Showing 49–64 of 252 results
-
Replacement Race Puller Plate Tool. Fits Mainshaft Bearing Race Tool # JM-34902-84.
$172.00Fitment Note: 2006-2017 Dyna & 2007up Models:- The bearing race is installed from factory with RED Locktite along with the trans pulley nut. This has been causing some problems. The two items must be heated prior to pulling the race or removing the nut with the sprocket wrench.
-
Race & Bearing Driver Handle Tool.
$209.00Features & Benefits:-* Race & Bearing Driver Handle Tool.* Use Handle with #’s JM-33071-73, JM-34810-84, JM-94547-80A, JM-94547-80B, JM-97272-60 & JM-97273-60. * Approximately 12in. long.Tech Tips:-* Replacement O’Ring # JM-2310.Proudly Made in the USA by JIMS !
-
-
36mm, Rear Axle Nut Wrench Tool. Use on Touring 2003up.
$109.00Suggested additional Purchase JM-970
-
Primary Drive Locking Tool. Fits All Models.
$129.00* Used to lock primary for service work* Fits between the chain and motor sprocket* Works on all primaries* Made out of black Delrin®* Made in the U.S.A.
-
Primary Chain Locking Bar Tool. Fits 4Spd Big Twin, Softail 1984-2006 & Dyna 1991-2005.
$77.00* Locks primary for service work* Made in the U.S.A.
-
Primary Chain Locking Bar Tool. Fits 6Spd Big Twin 2006up
$131.00* Locks primary for service workTech Tips:-* Will Not Fit Touring Models.* Made in the U.S.A.
-
-
Piston Ring Compressor Tool.
$367.00Features & Benefits:-* Fits all H-D Models.* Supplied with six bands.* Works with piston sizes from 2-7/8in. to 4-3/8in..* Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression.* Will Not Break or Damage Rings.Proudly Made in the USA by JIMS !
-
Piston Jet Tester Tool. Use on Milwaukee-Eight and Twin Cam Engines
$545.00A tool that every engine builder needs. This tool properly tests the pressure rating of each piston oiler jet before you final assemble your engines.
-
-
Pinion Gear Locking Tool. Fits Sportster 1991-1999.
$130.00* Use to lock pinion gear when torquing the pinion gear nut* Simple to use; just align underneath gear and screw into case* With Big Twin tool, use PART #DS-196147 to tighten pinion nut* Made in the U.S.A.
-
Pinion Gear Locking Tool. Use on Big Twin 1954-1999.
$383.00Bolts to case and locks pinion gear, necessary to torque the pinion nut. Use on Big Twin 1954-1999 single-cam engines.
Showing 49–64 of 252 results
Motorcycle Tools & Supplies Australia
Whether you’re servicing, repairing, detailing, customising or modifying your motorcycle, it pays to have a well-stocked toolkit in your workshop. Of course, you need to make sure your motorcycle tool kit is stocked with the best quality goods you can find. Having a large assortment of premium motorcycle tools and supplies may set you back in the short term, but the potential savings make it worthwhile in the long run. Plus your bike will thank you on the road with its performance.
What kind of tools do you need? While it depends on your level of work, some motorcycle accessories are useful staples that belong in every workshop. Tyre pressure gauges let you easily check that your tyres are properly inflated. Bolt kits contain a number of fasteners for various motorcycle components. Motorcycle lifts and floor jacks let you raise and lower your motorbike to make it easier for you to work on. And there are countless other components you can end up collecting if you end up getting deep into the art of motorcycle maintenance.
Taverner Motorsports provides a collection of general workshop equipment suitable for any good motorcycle tool kit, as well as tools that are specific to Harley-Davidson, Indian and Victory motorcycles. Whether you’ve just begun building your tool collection or you’re a seasoned DIY enthusiast, you can find whatever you’re looking for at Taverner’s online store or by dropping into our Bowen Hills workshop.
General Workshop Equipment
Taverner’s general workshop range includes plenty of gear suitable for all kinds of motorcycles, regardless of make or model.
Our motorcycle lifts and jacks differ in form and function but share the same purpose of raising and lowering your motorcycle so you can work on it. Lifts raise a motorbike into the air or onto a platform or table, while floor jacks raise it with a piston mechanism.
We also have a large selection of general hand tools, including driver spacers, belt tension gauges, shock spring compression tools, and dual gauge leakdown testers—among many others!
Our general shop supplies are there to equip you with the little bits and pieces that help hold your motorbike together, such as chrome zip ties. Oil lines and fittings lubricate various motorcycle parts, such as the engine and fuel pump. Taverner has components for these parts, such as stainless steel hose clamps, among our general workshop equipment.
Harley Davidson Specific Tools
If you’re a dedicated Harley-Davidson rider, you’ll be pleased to know that Taverner has an absolutely massive range of Harley-Davidson-specific tools. No matter what decade your Harley is from, we have accessories that are made to suit its unique design and engineering.
Check out our wheel bearing removal and installation tools, transmission pulley nut and locking tools, sprocket shaft installers, and tappet reamer tools, just to name a few. With hundreds of tools to choose from, you’ll easily be able to complete whatever work you have in mind for your Harley. Â
Indian & Victory Tools
Like Harley-Davidson, Indian and Victory motorcycles often require their own tools for their unique designs. You can find these tools, such as water pump seal installers and wheel bearing hub protectors, right here on the Taverner site.
Over the decades, Taverner has built strong relationships with parts suppliers worldwide, and we use only the best brands for our motorcycle parts. For more information about our motorcycle tools and help building your motorcycle tool kit, get in touch with the Taverner team.Â