Showing 49–64 of 222 results
-
$844.00
Kit Includes:* Chrome Trapdoor with installed bearings & retainers* Purchase gasket # JGI-35653-98 seperatly* Can also be used to upgrade 1980-98 models to the later in.bigin. trap door bearing* Replaces OEM # 35252-93 & is an upgrade on OEM # 35258-87Proudly Made in the U.S.A.
-
$1,125.00
* This rebuild kit has been created by JIMS to help make rebuilding your H-D 6-speed Cruise Drive transmission simpler by combining all the parts needed under one part number.* Kits come with the gaskets, seals, locks and bearings required to rebuild a 6-speed transmission* Made in the U.S.A.
-
$1,169.00
* This rebuild kit has been created by JIMS to help make rebuilding your H-D 6-speed Cruise Drive transmission simpler by combining all the parts needed under one part number.* Kits come with the gaskets, seals, locks and bearings required to rebuild a 6-speed transmission* Made in the U.S.A.
-
$536.00
Requires the below to complete:* 2 x JM-35961-52 = Brg; C/Shaft BT’77-84(2req)* 1 x JM-9020 = Brg; Trans Main BT’36-86 4spd * 1 x 25451 = Brg; M/Drive Gear BT’82-86 4spd* 1 x JM-8905 = Brg; Main Drive Gear BT’77-81* Use Jims Shift fork Align tool # JM-96385-78A* We use JIMS# proven transmission parts to…
-
$235.00
Features & Benefits:-* Remove & Install.* The shifter shaft bushing cannot be pressed through to remove it requiring this JIMS specialty tool. This new JIMS tool is designed to remove the old bushing with a unique knurled driver and receiver cup. A new installation driver is included in the kit to correctly install a new…
-
$135.00
Features & Benefits:-* Use with the Clutch Spring Compressor Tool # JM-38515-90.Tech Tips:-* Will Not Fit XR1200.Proudly Made in the USA by JIMS !
-
$180.00
The new M8™ engine uses different wrist pins compared to other Harley-Davidson® engines. This tool quickly and easily removes the wrist pins in these new engines. To reduce cost and save tool box space, this adapter is used with our existing wrist pin tool No. JM-1276 (purchased separately)
-
$107.00
Features & Benefits:-* Replacement Jims Wheel Bearing Puller .750in. I.D.Proudly Made in the USA by JIMS !
-
$169.00
Features & Benefits:-* Replacement 25mm Puller Only.Proudly Made in the USA by JIMS !
-
$134.00
Features & Benefits:-* Replacement Jims Wheel Bearing Puller 1.00in. I.D.Proudly Made in the USA by JIMS !
-
$202.00
Features & Benefits:-* Removes & installs the 25mm H-D bearing.* Removes ABS or non ABS Wheel Bearings on most of 2008up Wheels. * This tool must be used with the earlier JIMS wheel bearing Installer & Remover Tool # JM-1042.Proudly Made in the USA by JIMS !
-
-
$518.00
Suggested Additional Purchase* Features a hardened ball-bearing at the valve head end to eliminate damage to valves* Comes with new valve collar receiver for safer tool usage* Made in the USA!Tech Tips:-* 2005-2017 Require Adapter Part Number: JM-988 * 2017up(M8) Require Adapter Part Number: JM-5808
-
-
$180.00
Features & Benefits:-* Short Socket.* Designed to Remove, Install & Properly Tighten the Front Final Drive Sprocket/Pulley Nut.* Although the much longer Big Twin socket will fit the nut, the Mainshaft on XL models does not extend through for the guidance collar to ensure correct alignment. * This shorter socket is easier and safer to…
-
$463.00
Features & Benefits:-* Fits 4 & 5 Speed Models* Heavy-Duty thick wall tube. * Extra long two piece design, inner collar will retain wrench to nut for safer service work.* 1-7/8in. hex.* 1/2in. Drive.Tech Tips:-* Will Not Fit 6 Speed Transmissions.Proudly Made in the USA by JIMS !
Showing 49–64 of 222 results