Mainshaft Right Case Bearing. Fits Sportster 1984-1990.
$46.00American made by Torrington#. Install bearing with JIMS# Mainshaft Bearing Tool No.34810-84.Replaces OEM # 9118
Showing 33–48 of 222 results
American made by Torrington#. Install bearing with JIMS# Mainshaft Bearing Tool No.34810-84.Replaces OEM # 9118
Features & Benefits:-* 4 Required per Transmission.* Proudly Made in the USA.* Replaces OEM # 8876
The 34091-85 inner bearing race has been used on Big Twins since 1985. The inner primary bearing rides on this race. By design, this race press-fits onto the transmission mainshaft. This system works fine for stock engines. 100 HP+ engines will make this bearing walk on the mainshaft. If it walks inboard, it will damage…
* 4 Required.* Sold Each.* Replaces OEM # 9057American made by Torrington. For the best results install bearing with JIMS# Cam Bearing Installation JIMS# Tool No.97273-60. To remove bearing use JIMS# Tool 95760-XL.
* Includes 2 x Bearing, Washers & Clip.* Kit comes with U.S.A. made bearing. * Since this kit is made to JIMS# high standards, it ensures proper clutch operation. * Replaces H-D# No.#s 37312-75, 37313-80 and 11096* Made in the U.S.A.
* Use on Sportster# and K models 1954-90. Use on Buell# 1987-90* Replaces OEM # 35960-54
Features & Benefits:-* Primary Side Closed Bearing.* Fits Evo 1980-1999.* Fits Twin Cam 1999-2006 with 5 Speed Transmission.* Fits Sportster 1991-2005.* Fits Buell 1991-2005.* Proudly Made in the USA!* Replaces OEM # 8977
Features & Benefits:-* Fits Big Twin 1977-1984 (2 Required).* Fits Sportster 1954-1984 (2 Required). * Fits Sportster 1985-1990 (3 Required).* Fits Buell 1987-1990 (3 Required).* Replaces OEM # 35961-52American made by Torrington. For the best results install bearing with JIMS countershaft Bearing Tool No. JM-34733-77.
* Use in fifth gear – 2 requires per transmission. * Install with JIMS# Tool # JM-34734-80 to the right depth* Replaces OEM # 8904
These American made Torrington# rod bearing sets consisting of three packaged bearings with 16 rollers in steel cages. They will retro fit back to 1941. They are available in a standard size only. When refitting rods, use this set with JIMS# oversize crankpins.
Fitment Note: 2006-2017 Dyna & 2007up Models:- The bearing race is installed from factory with RED Locktite along with the trans pulley nut. This has been causing some problems. The two items must be heated prior to pulling the race or removing the nut with the sprocket wrench.
Features & Benefits:-* Machined from solid bronze bar stock.* Hold concentricity to less than .0002in..* Includes Sprocket Shaft # JM-23909-80.* Includes Sprocket Side Nut # JM-24003-55.* Flywheel Side Nut # JM-24017-80.* Key # JM-2489.Proudly Made in the USA by JIMS !
Jims A Cut Above Time-Saver 5-Speed Transmission Master Kit* Kits include bearings, retaining rings, spacers, locknuts and gaskets and seals for Big Twin* Made in the USAWe use JIMS# proven transmission parts to start with, then top it off with a JIMS# gasket set, together in one convenient package. This is a big time saver.Tech…
Features & Benefits:-* Short Socket.* Designed to Remove, Install & Properly Tighten the Front Final Drive Sprocket/Pulley Nut.* Although the much longer Big Twin socket will fit the nut, the Mainshaft on XL models does not extend through for the guidance collar to ensure correct alignment. * This shorter socket is easier and safer to…
Features & Benefits:-* Fits 4 & 5 Speed Models* Heavy-Duty thick wall tube. * Extra long two piece design, inner collar will retain wrench to nut for safer service work.* 1-7/8in. hex.* 1/2in. Drive.Tech Tips:-* Will Not Fit 6 Speed Transmissions.Proudly Made in the USA by JIMS !
Showing 33–48 of 222 results
No products in the cart.