Showing 17–32 of 222 results
-
$180.00
The new M8™ engine uses different wrist pins compared to other Harley-Davidson® engines. This tool quickly and easily removes the wrist pins in these new engines. To reduce cost and save tool box space, this adapter is used with our existing wrist pin tool No. JM-1276 (purchased separately)
-
$918.00
* Includes: 3/4in., 1in. & 25mm bearing pullers* This tool is designed to remove and install sealed type wheel bearings without damaging the wheel.
-
$285.00
* Easy-to-use race installer/remover tool by JIMS* Eases removal or installation of bearing cups* Use in conjunction with the handle/driver PART #JM-33416-80 (sold separately)* Made in the U.S.A.
-
$107.00
Features & Benefits:-* Replacement Jims Wheel Bearing Puller .750in. I.D.Proudly Made in the USA by JIMS !
-
$169.00
Features & Benefits:-* Replacement 25mm Puller Only.Proudly Made in the USA by JIMS !
-
$134.00
Features & Benefits:-* Replacement Jims Wheel Bearing Puller 1.00in. I.D.Proudly Made in the USA by JIMS !
-
$202.00
Features & Benefits:-* Removes & installs the 25mm H-D bearing.* Removes ABS or non ABS Wheel Bearings on most of 2008up Wheels. * This tool must be used with the earlier JIMS wheel bearing Installer & Remover Tool # JM-1042.Proudly Made in the USA by JIMS !
-
-
$518.00
Suggested Additional Purchase* Features a hardened ball-bearing at the valve head end to eliminate damage to valves* Comes with new valve collar receiver for safer tool usage* Made in the USA!Tech Tips:-* 2005-2017 Require Adapter Part Number: JM-988 * 2017up(M8) Require Adapter Part Number: JM-5808
-
-
$180.00
Features & Benefits:-* Short Socket.* Designed to Remove, Install & Properly Tighten the Front Final Drive Sprocket/Pulley Nut.* Although the much longer Big Twin socket will fit the nut, the Mainshaft on XL models does not extend through for the guidance collar to ensure correct alignment. * This shorter socket is easier and safer to…
-
$463.00
Features & Benefits:-* Fits 4 & 5 Speed Models* Heavy-Duty thick wall tube. * Extra long two piece design, inner collar will retain wrench to nut for safer service work.* 1-7/8in. hex.* 1/2in. Drive.Tech Tips:-* Will Not Fit 6 Speed Transmissions.Proudly Made in the USA by JIMS !
-
$172.00
* Used to remove and install top fork-tube plug* Fits 41mm forks* Made in the U.S.A* Note: this tool works on the top fork plug that screws into the fork tube.* Slider tube cap socket JM-2244 may also be required
-
$218.00
35mm Slider tube top cap nut. Use’s 3/8in. drive* Used to remove and install top fork nuts on fork tubes* Rubber protector inside socket protects chrome finish* Will clear under most handlebars* Made in the U.S.A.
-
$352.00
Installing fork tube caps requires compressing the spring while rotating the cap. This is not particularly difficult with fork legs that have been removed from the bike and securely mounted in a work area. However, on the bike, the task can become almost impossible because of restricted work area and other components getting in the…
-
$203.00
The new Softail inverted forks utilizes a unique inner fork nut (Castlenut) to secure and compress the fork spring. This one-piece solid steel socket is designed to help the technician by securing the socket to the joint rod prior to final assembly.Fitment:M8 Softail with Inverted forks (i.e. FXDR, Sport Glide, Fat Bob, Low Rider SV-Rod…
Showing 17–32 of 222 results