Showing 145–160 of 220 results
-
Clutch Hub Puller Tool. Use on Big Twin 1936-1989
$239.00Features & Benefits:-* Removes the Three (3) Stud Dry clutch hub on Big Twins 1936-1984* Removes Four (4) Stud Wet clutch hub on Big Twins 1984-1989Tech Tips:-* Use the three holes marked DC for 1936-84 three Stud Dry Clutch.* Use the four screws & the holes marked WC for 1984-89 four stud Wet Clutch.* Does…
-
Clutch Hub Puller Tool. Use on Big Twin 1936-1989 & Sportster 1954-1989.
$227.00Features & Benefits:-* Assist in removing, Big Twin 1936-Early 1984 clutch hub 3, 5 or 10 Stud with H-D dry clutch.* Assist in removing, WLA (45ci) clutch hubs.* Assist in removing, Early Big Twin non-compensating motor sprockets. * Assist in removing, Alternator Rotors Big Twin 1970up.* Assist in removing, Sportster Clutch Hubs 1954-1989.* Assist in…
-
Camshaft Remover & Installer Tool. Fits Twin Cam 1999-2006.
$496.00Features & Benefits:-* Used to remove & install camshafts & bearings.* Provides precision alignment of camshafts in the support plate.Tech Tips:-* Will Not Fit Dyna 2006.Proudly Made in the USA by JIMS !
-
Cam & Crank Gear Locking Tool. Fits Twin Cam 1999-2006.
$143.00Features & Benefits:-* Designed to lock the camshafts & crankshaft sprockets when removing, replacing & torquing the sprocket bolts.* Made of non-marring Delrin.* Includes Instructions.Tech Tips:-* Will Not Fit Dyna 2006.Proudly Made in the USA by JIMS !
-
Cam Gear Locking Tool. Use on Twin Cam 2007-2017 & Milwaukee-Eight 2017up.
$190.00* Also fits Milwaukee 8* Designed to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket bolts* Made of non-marring Delrin* Instructions included* Made in the U.S.A.
-
Cam Chain Tensioner Tool. Fits Twin Cam 1999-2006.
$136.00Features & Benefits:-* Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams.* Also checks spring loads on chain tensioners* Includes instructionsTech Tips:-* Will Not Fit Dyna 2006.Proudly Made in the USA by JIMS !
-
Cam Bearing Installer Tool. Fits Big Twin 1958-1999 with Single Cam.
$418.00* Presses in the inner cam bearing* Designed to press from letter side of the inner cam bearing by putting all the pushing pressure to the very outer wall of bearing shell* Eliminates any damage to the bearing, cam and cases* Stops at the case and sets the bearing depth to .023in. to .028in. below…
-
-
Alternator Rotor Remover & Installer Tool. Use on Milwaukee-Eight 2017up.
$503.00Removing or installing the high output alternator rotor on the M8™ requires a unique tool, and trust us – those magnets donÂ’t budge easily! At JIMS we understand that using pry bars or striking with a hammer can not only damage the rotor housing, but the magnets as well. This tool easily removes the rotor…
-
-
Timken Bearing Conversion Tool
$2,892.00Features & Benefits:-* Suggested additional purchase, Timken Bearing # SS31-4013Tech Tips:-* May cause a slight increase in engine noise
-
Tappet Position Holding Tool. Fits Twin Cam 1999-2017, Milwaukee-Eight 2017up & Sportster 2000-2021.
$154.00* This tool allows the tappets and anti-rotation pins to be safely and accurately stored for proper reinstallation.* Tappet locations are clearly referenced on the tool which also serves to protect the tappets from damage when removed from the engine.
Showing 145–160 of 220 results