Tyre Pressure Gauge – 0-60 PSI Read Out. Black Face
$54.00Tire Gauge with 0-60 PSI read out for use on standard schrader valves
Showing 17–32 of 167 results
Tire Gauge with 0-60 PSI read out for use on standard schrader valves
Features & Benefits:-* Also Gear Drive Backlash.This tool simplifies and speeds the process of checking crankshaft run out on both M8 model engines with the crankshaft installed. The tool mounts to the cam chest side of the engine case using the designated mounting holes of the tool combined with the handled thumb screws and the…
This tool simplifies and speeds the process of checking crankshaft run out on both Twin Cam and EVO model engines with the crankshaft installed. The tool mounts to the cam chest side of the engine case using the designated mounting holes of the tool combined with the handled thumb screws and the case cam cover…
* This pressure test tool is a must for any Twin Cam engine builder. Bench test the camplate before installation, cycle the pressure relief valve testing operation assuring the valve moves freely, seats and seals. Leakage at the relief valve will reduce oil pressure.* This tool allows the engine builder to know what PSI the…
Features & Benefits:-* VVT M-Eight Cam Bolt Torque reaction tool. This tool allows removal and instal of the VVT cam bolt, referenced by the factory as the spool valve.Proudly Made in the USA by Feuling !* Replaces OEM # HD-53289
Features & Benefits:-* Designed with a tighter tolerance on the ID for better fit on the pinion shaft * Helps to eliminate the timing variance (up to 4 degrees) that is associated with the loose fitting factory sprockets.* Replaces OEM # 25673-06Tech Tips:-* Due to variations in pinion shafts, Fueling have gone a little smaller…
* Increase the camplate pressure relief pop off pressure with a Feuling spring.* Our spring has the proper spring rate to control the pop off pressure and oil flow in bye pass port.* Bench testing recommended with the Feuling camplate pressure test tool FE-9010 set your pop off pressure to your preference.* Replaces OEM #…
* Camshaft sprocket spacing alignment/thrust washer kit. * Alignment washers are used to align the rear camshaft sprocket with the crank sprocket to achieve correct chain alignment. * Kit includes front cam thrust washer 0.100in. & rear cam sprocket alignment washers 0.110in., 0.120in., 0.130in., 0.140in., 0.150in..
* Sold as a pack of 5* Camshaft sprocket spacing alignment/thrust washer. * Alignment washers are used to align the rear camshaft sprocket with the crank sprocket to achieve correct chain alignment. * Pack includes 5 x 0.130in. front cam thrust washer* Replaces OEM # 25736-06
* Sold as a pack of 5* Camshaft sprocket spacing alignment/thrust washer. * Alignment washers are used to align the rear camshaft sprocket with the crank sprocket to achieve correct chain alignment. * Pack includes 5 x 0.120in. front cam thrust washer* Replaces OEM # 25734-06
Twin Cam engine bolt kit: Cam cover, Lifter blocks, Rocker box, Case bolts, Oil filter adapter, Crank sensor, Exhaust studs
External primary and transmission Kit: Primary cover, derby cover, top transmission cover, right transmission bearing housing, clutch release cover, sensors and engine to transmission mounting bolts.Fits: Milwaukee Eight ’17 Up Touring models
External Engine kit: Cam cover, lifter block covers, rocker covers, case bolts, oil lines, volt regulator, exhaust studs and locking nuts, Moly lube and Loctite
M8 Softail 18 Primary and Transmission Stainless 12 point kitA SHOW polish and corrosion-resistant finishPrimary Cover Primary Cover W/ WashersEngine to Trans – Bottom, use WasherEngine to Trans – Top, Use WasherDerby Cover use washers Trans Clutch Release CoverTrans Clutch Release Cover use washersTrans Bearing Housing Cover use washersTransmission Top Cover use washersOil Cooler Bracket…
M8 Softail External Engine 12 Point Stainless Bolt Kit8 Cover for front & rear Lifters9 Cam Cover 20 Cover for Rocker Front & Rear 20 Washers 2 Center Head Bolts / Horn/ Engine mount4 Oil Line Mounting Bases2 Front Head Mount Bolts2 Front Head Stabilizer Mount Bolts W/ HD Washer4 Exhaust Studs4 Exhaust Nuts12 Case…
Kit Includes 6 of 3 thicknesses: 0.003, 0.005, 0.0010Features & Benefits:-Quiet your engine by tightening the rocker arm to cylinder head end play clearance. FEULING recommends an ideal side clearance of 0.035 – 0.005 for optimum rocker arm oil psi and noise reduction. M-Eight cylinder heads also have excessive wear on the rocker arm standoff…
Showing 17–32 of 167 results